About Stevens System Accuracy Contact Us CAD  Library Product Search What's New
  Modular Fixturing System -   / Products / Accesories / Edge Locators

EDGE LOCATORS & ACCESSORIES

[ Flat | Round | Brackets | Bracket Slides | Bracket T-Nuts | Bars ]

FLAT LOCATORS
Used For Additional Flexibility In Edge Location.
  • 2 vertical reference surfaces are used for accurate edge location.
  • Threaded hole in one face allows use of Rest Pads and Shims to build up rest surfaces to any desired distance from a bushed hole location.
  • Uses locking collet mechanism to mount into Stevens bushed holes. Extractor can be used for removal after loosening collet with Allen wrench.
  • Material: Alloy steel, case hardened to 60Rc.

PART NO.  
20077  
APPLICATIONS

 

ROUND LOCATORS
Used For Accurate And Repeatable Location Of Workpiece Edges.
  • Fits Stevens bushed holes.
  • Unique locking device secures the edge locator firmly in place using an Allen wrench. To remove, loosen with Allen wrench and use extractor.
  • Dimension from centerline to point of tangency is the same as the centerline to edge dimension for all other edge locators and Utility Blocks.
  • Material: Alloy steel, case hardened to 60Rc.

PART NO.  
20076-1  

PART NO.  
20076-2  

PART NO.  
20076-3  

PART NO.  
20076-4  

 

APPLICATION

  • Round Edge Locators may be used in pairs as a vee block.

 

Edge Locator BRACKETS
Used For Flexible Positioning Of A Wide Variety Of Locators.
  • Vertical slot on front face allows positioning of locators such as Rest Pads and Vee Locators.
  • Clamps may also be mounted on Edge Locator Bracket using the Bracket T-Nut.
  • Perpendicularity:   .0005”
  • Material:  Alloy steel, case hardened to 60Rc.

PART NO.  
10258  
APPLICATION

  • The vertical face of the Edge Locator Bracket may be positioned with great accuracy relative to bushing locations using gage blocks or calipers and the Edge Locator Bar.

 

 

Edge Locator BRACKET SLIDES
Used For Lateral And Vertical Positioning Of Locators On Edge Locator Bracket.
  • 2-piece assembly consists of a Slide Nut and a Slide Body which fits the vertical slot on the Edge Locator Bracket.
  • Vertical position is fixed using a cap screw.
  • Horizontal position of the locator is fixed by moving the slide nut laterally until the desired position is reached, then inserting and tightening the locator in the threaded hole in the Slide Nut.
  • .8000 dimension is closely qualified, allowing Stevens Rest Pads and other locators to be set at known locations relative to the face of the Edge Locator Bracket.
  • Material: Alloy steel, case hardened to 60Rc.

PART NO.  
20123  
APPLICATIONS

 

Edge Locator BRACKET T-NUTS
Used With Edge Locator Bracket For Clamping.
  • One of the two threaded holes is used to fasten the Bracket T-nut at the desired height using a cap screw; the other hole is used to mount a clamp screw.
  • Material: Hardened alloy steel.

PART NO.  
10261  
APPLICATION

 

Edge Locator BARS
Used As A Precise Edge Locator When Greater Contact Length Is Needed.
  • Side edge and end are qualified with respect to bushing centerline.
  • Height is qualified, allowing use of edge locator bars as precision parallels.
  • Material: Alloy steel, case hardened to 60Rc.

PART NO.  
20176-1  

PART NO.  
20176-2  

 

APPLICATIONS

Stevens Engineering, Inc., 3946 W. Clarendon Avenue, Phoenix, AZ 85019
1-(800)635-0657 or (602)272-6766 - FAX (602)272-0717

info@stevenseng.com

E-Mail Webmaster  ©2005 Stevens Engineering, Inc.